Sunday, May 27, 2012

Roof and Solar Install

The active period continues and just last week we completed our solar installation immediately after the roof install.  The photo shows the Schuco racking in place and the first day of panel installation is nearly over.  The racking took one day to install, with the 45 250W poly panels an additional two days.  Roof pitch is 8/12 - walkable, but not that comfortable.

Notes:
Schuco rails are heavy duty.  We received our rails from our supplier DTE Solar's old stock.  This was fortunate since the rails were a full 20' long.  The new products out there are apparently available in standard 10' lengths only.  Longer lengths are special order.  I was glad we were able to get these longer lengths.  The L brackets, which are attached to the roof throuth the shingles and into the rafters with 1/4" x 3.5" stainless lag screws are mounted along each rail, 4' OC.  Pre-drilled mounting, with a special flashing that tucks under the shingles and sealant is applied under the brackets as well.  This is a long and messy job - the mounting of all these brackets.  It is also very permanent.  Once in place, it becomes an issue to repair the roof under these feet.  And all the traffic on the roof in warm weather has really worn down the shingles.  Especially near the scaffold.  However, we are expecting the shingles will last a long time due to their being protected a great deal by the panels.

Note:  We originally intended to go with a standing seam metal roof.  Price for our Vicwest Tradition 100 22ga painted steel roof was $7.50/SF (this is a very thick sheet metal gauge for steel roofs), compared with $2.30/SF for the shingles (including full Ice and water on the south side and ridge vent).  Major difference in cost, but we were totally willing.  It would have been an excellent looking roof, but also extremely long lasting, recyclable, good for rainwater collection (no much concern of the tar from shingles), and waterproof.  In addition, the solar panels would have been mounted directly to the steel seams with S-5! clamp mounts, giving a very sleek and low-profile integrated panel install.  Unfortunately, the timing didn't work out and we had to meet our microFIT deadline, so we went with a shingle roof (not to mention we are elated at the cost savings).

HOWEVER:  One thing to keep in mind:  The metal roof with the S-5! mounting would have been a very versatile roof/solar system, because the S-5! clamps can mount anywhere along the seams, and there are no penetrations through the roof.  The rail system is quite a downgrade (although significantly more expensive than the S-5!) in my view because once those rails are in place, they are not moving.  Whatever the future brings, it must go on those rails.  And one thing I'd like to see in the future is that we increase the number of panels on the roof - no chance with those rails - with the S-5!, it would have been simpler, I think.  I do foresee that people will want solar PV even beyond the microFIT limits.  I certainly do - the cost is so reasonable right now, and I feel it can be made even cheaper by not using the inverters - for example solar PV water heating can do fine with DC - no need for AC.

The panels are on a portrait layout, 3 rows of 15 panels for a total of 45.  6 Rails, 2 for each row of panels.  The rails have a splicing hardware which is basically a bar that slides into the rail grooves and screws in place.  Note, with the metal roof and S-5! clamps, it would have been a landscape layout. We have two 5kW 'Power One' inverters for a total output of 10kW.  The array is rated at 250x45 panels for total of 11,250W.  One is allowed to install up to 12kW for a 10kW system capacity.  We could add 3 panels to the system - perhaps on the garage in back?  Each inverter takes 2 channels of DC input.  We have therefore divided the array into 4 blocks - 3 with 11 panels and one with 12 panels.  This uneven-ness is no problem for the inverters to handle (without any loss of energy to speak of).

What is annoying to me is the system architecture mandated by the MicroFIT program.  It centres around this Anti-Islanding feature.  Simply, the system is not configured (and cannot be configured, I'm told) to provide the homeowner directly with power, bypassing the grid.  In other words, the array serves the grid only, and the inverters shut off automatically if they detect no grid.  This means they cannot be used to provide the household with power.  Personally I hate this - it means there is no redundancy benefit for the owner.  When the grid is down (during a blackout), so is our own generation system.  This serves to protect hydro workers from being exposed to electricity while they repair the grid.  Investigation is needed to see if there is a safe and legitimate way around this.



11 comments:

  1. A fantastic presentation. Very open and informative.You have beautifully presented your thought in this blog post.


    Solar Racking Manufacturers


    Feed in tariff program

    ReplyDelete
  2. This is awesome, I never would have thought of when getting a house built, to pre-install it with solar panels. How much did that cost in addition to the entire construction?

    -Sharone Tal

    ReplyDelete
    Replies
    1. Cost on this 11.25kW system was about $5/watt. It was a big chunk of our construction budget, but it also means we are generating income long before the construction project is finished.

      Delete
  3. Thats a great move you are taking, thanks for sharing

    MicroFIT Solar

    ReplyDelete
  4. It looks like they put that roof up relatively within minutes... How did they pull off such flawless execution?

    -Adam Ahmed

    ReplyDelete
  5. Solar technology reduce over electricity expense and save our time which we waist during storage of electric.
    moving boxes Toronto

    ReplyDelete
  6. I am happy to find this post very useful for me, as it contains lot of information. I always prefer to read the quality content and this thing I found in you post.

    Visit Jones Roofing

    ReplyDelete
  7. I likes your post, thanks for giving such a nice suggestions and ideas about roofing.
    toronto roofing

    ReplyDelete
  8. That's quite fast! Your solar panels were immediately installed right after the roof was completed. Most people only consider installing solar panels after they've finished with the rest of the house. Also, I am curious of how durable your roofing materials are? Most solar panel systems are designed to last around 25 years or so, but most roofs, by that time, have to be replaced already.

    Maggio Roofing

    ReplyDelete
  9. This comment has been removed by a blog administrator.

    ReplyDelete